Versions available: |
| Drawings - 2DNY 201 |
| 1 CI CHIMNEY BASE - D 1 |
| 1 CI CHIMNEY (INC TOP) - D 2 |
| 1 CI CHIMNEY BOTTOM RING - D 3 |
| 1 CI SMOKE BOX DOOR - D 4 |
| 1 CI SMOKE BOX DOOR RING - D 5 |
| 1 CI CYLINDER - D 6 |
| 1 CI CYLINDER FRONT COVER - D 7 |
| 1 CI CYLINDER BACK COVER - D 8 |
| 1 CI TOP STEAM DOME - D 9 |
| 1 CI VALVE CHEST COVER - D 10 |
| 1 CI VALVE CHEST - D 11 |
| 1 CI CYLINDER LINER - D 12 |
| 1 GM REGULATOR GLAND - D 13 |
| 1 GM VALVE CHEST GLAND - D 14 |
| 1 GM CYLINDER GLAND - D 15 |
| 1 CI PISTON - D 16 |
| 1 GM CROSSHEAD - D 17 |
| 1 GM SLIDE BAR BRACKET - D 18 |
| 1 GM SLIDE VALVE - D 19 |
| 1 GM REGULATOR BLOCK - D 20 |
| 1 GM CRANK SHAFT BEARING BKT. - D 21 |
| 2 req.(Price per single casting) GM CRANK SHAFT BEARING CAP - D 22 |
| 1 GM CRANK SHAFT BEARING BRASS - D 23 |
| 1 GM WEIGH SHAFT BKT. RH. - D 24 |
| 1 GM WEIGH SHAFT BKT. RH. - D 25 |
| 2 req.(Price per single casting) GM BEARING BRASSES - D 26 |
| 1 CI FLYWHEEL - D 27 |
| 2 req.(Price per single casting) CI ECCENTRIC STRAPS - D 28 |
| 2 req.(Price per single casting) GM SAFETY VALVE BODY & ADJ. CENTRE - D 29 |
| Not used. - D 30 |
| 2 req. (Price per single wheel) MS FRONT WHEELS - D 31 |
| 2 req.(Price per single wheel) MS REAR WHEELS - D 32 |
| 2 req.(Price per single casting) CI FRONT HUB - D 33 |
| 2 req.(Price per single casting) CI REAR HUB - D 34 |
| 2 req.(Price per single casting) GM 2nd MOTION SHAFT & HIND AXLE. - D 35 |
| 2 req.(Price per single casting) GM AXLE BOX - D 36 |
| 1 GM PERCH FORK - D 37 |
| 1 GM BOTTOM & TOP PERCH BUSH - D 38 |
| 1 GM MEC. LUB. CY. BODY & VALVE - D 39 |
| 1 CI LOW SPEED GEAR - D 40 |
| 1 CI HIGH SPEED BELL GEAR - D 41 |
| 1 CI 2nd SHAFT LOW SPEED GEAR - D 42 |
| 1 CI 2nd SHAFT HIGH SPEED GEAR - D 43 |
| 1 CI FINAL DRIVE GEAR. 2nd SHAFT - D 44 |
| 1 CI FINAL DRIVE GEAR ON HIND AXLE - D 45 |
| 1 GM WINDING DRUM KEEP PLATE - D 46 |
| 1 CI WINDING DRUM - D 47 |
| 1 CI WINDING DRUM INNER HUB - D 48 |
| 1 GM WATER POCKET - D 49 |
| 1 GM WATER LIFTER - D 50 |
| 1 GM PUMP BODY - D 51 |
| 1 GM GLAND FLANGE - D 52 |
| 1 GM PUMP ECCENTRIC STRAP - D 53 |
| 1 GM STEERING WHEEL - D 54 |
| 1 GM TOP STEERAGE SPINDLE BKT - D 55 |
| 1 GM BOTTOM STEERAGE SPINDLE BKT - D 56 |
| 1 GM STEAM TURRET - D 57 |
| 2 req.(Price per single casting) GM WATER GAUGE PILLAR - D 58 |
| 1 GM REGULATOR LEVER BKT - D 59 |
| D. 60 1 GM STEAM ELBOW - D 60 |
| 1 GM GOVERNOR BKT - D 61 |
| 1 GM GOVERNOR HEAD - D 62 |
| Not used. - D 63 |
| 1 GM GOVERNOR VALVE - D 64 |
| 1 GM SUET LUBRICATOR BODY - D 65 |
| 1 CI COMPENSATION CENTRE - D 66 |
| 1 CI COMPENSATING RING GEAR - D 67 |
| 2 req. (Price per single casting) CI BEVEL GEARS - D 68 |
| THE PICTURE ABOVE SHOWS A FINE 4" VERSION BUILT TO A VERY HIGH STANDARD - D 000 |
PRICES LISTED BELOW ARE FOR THE 2" VERSION 4" TO FOLLOW SOON CHECK BOTTOM OF PAGE FOR MACHINED GEARS ETC - SPECIAL OFFER FOR FULL SET OF CASTINGS ETC. -
PRICES ARE FOR ONE ITEM ONLY |
| BRASSES - D 150 |
| ROLLED SMOKE BOX - D 158 |
| CRANK BLANK - D 154 |
| SPOKES FRONT - D 155 |
| Spokes are laser cut, clean and accurate. Sold as a set for two wheels. |
| SPOKES REAR - D 156 |
| Spokes are laser cut, clean and accurate. Sold as a set for two wheels. |
| AXLE BLANK - D 157 |
| COPPER BOILER - D 163 |
| poa |
| COPPER BOILER KIT - D 164 |
| poa |
| HORNPLATES - D 166 |
| Hornplates are laser cut and are clean and accurate. |
| GEARS - D 190 |
| Full set of road gears, spurs, bevels and pinions, including castings, machining, gear cutting, keyways. |
| GEARS - D 191 |
| Pump gears - Finished |
| GOVERNOR GEARS - D 194 |
| Finished gears |
| STEERING WORM & GEAR - D 195 |
| Finished gears |
| CHIMNEY BASE - DD1 |
This very popular single cylinder engine is of straight forward design and ideally suited for the first-timer in 2" scale, and for those who want to go to 4" scale, absolutely first class. Both models have the very elegant Victorian slater spring safety valves sitting majestically on top of the cylinder casting as the finishing touch.